Blodgett No Heat Error: the combi oven is not warming up
When the control asks for cavity heat, it expects the temperature to move.
Mon–Sat, 8am–8pm
- Temperature and alarms
- Reach-in and prep table repair
- Source: Blodgett
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What No Heat Error
actually means.
When the control asks for cavity heat, it expects the temperature to move. If the cavity probe shows less than a 1°F rise over 5 minutes, the control shows No Heat Error. On gas models an interrupted gas supply or a failed ignition is the usual story; on electric models, an element or contactor.
Blodgett commercial appliance display · also shown as No Heat Error
What to do when No Heat Error shows on the commercial applianceKind of codeTemperature and alarms
The controller has seen a temperature outside the band it was set for and is saying so: a box above its alarm point, a fryer vat or an oven cavity that tripped its high-limit, or a dish machine rinse that never came up to heat. Often the cause sits outside the unit, such as a door left open during a delivery, a coil packed with grease, a kitchen far hotter than the maker allows or a booster fed cold water. Checking the door, the coil and the air around the unit is fair; move the product if a cold box stays above 41°F, and book the visit.
Usually leads toReach-in and prep table repair
Reach-ins, pass-throughs, prep tables and blast chillers: gaskets, hinges, fans, thermostats, condensers and compressors.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeBlodgett
A Blodgett visit tends to land early in the morning, before the first sheet pans go in and while the cavity is still cold.
SourceBlodgett MenuSelect BC20 control service guide
Blodgett BC-20 combi ovens with the MenuSelect control (MenuSelect BC20 service guide).
Before you book,
in this order.
Each step comes from Blodgett's own guidance for No Heat Error on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
On gas models, confirm the oven gas valve is open and that the other gas equipment on the line lights; if you smell gas, leave the building and call the utility from outside.
On electric models, check the breaker for the oven.
Restart once; if No Heat Error returns, arrange service for ignition or heating parts.
Still there?
It usually turns into reach-in and prep table repair. Book with the code and the model number.
What not to do
No Heat Error is not a probe problem; the probe is reading, and it reads no change. A cavity that overheats shows Cavity High Temp Error instead.
What you may
notice with it.
The commercial appliance problems No Heat Error tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where No Heat Error usually leads
Reach-in and prep table repair.
Blodgett
commercial appliances.
A Blodgett visit tends to land early in the morning, before the first sheet pans go in and while the cavity is still cold.
Blodgett commercial appliance repairMore Blodgett codes
Temperature and alarms on other makes
In Blodgett's own words
The cavity probe temperature does not raise 1F in 5 minutes during a call for cavity heat.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Blodgett BC-20 combi ovens with the MenuSelect control (MenuSelect BC20 service guide).
Blodgett No Heat Error commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about No Heat Error.
Can I clear No Heat Error myself?
Why does my Blodgett gas combi show No Heat Error after a gas shutoff?
How long does a Blodgett wait before No Heat Error?
Is No Heat Error on a Blodgett dangerous?
Back to your everyday
Still showing No Heat Error?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.