The small controller display on the front of a stainless commercial reach-in cabinet in a restaurant kitchen, the display lit with no characters readable, the reach-in's doors closed, nobody at the unit.

Continental Loc: the EVCO keypad is locked

The EVCO control on some Continental units locks its keys after 30 seconds without a touch, so a bumped button cannot change the set point.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Mode, not a failure
  • No repair needed
  • Source: Continental Refrigerator

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What Loc
actually means.

The EVCO control on some Continental units locks its keys after 30 seconds without a touch, so a bumped button cannot change the set point. Pressing and holding any key shows Loc, then UnL once the keypad unlocks.

Continental Refrigerator commercial appliance display · also shown as UnL

What to do when Loc shows on the commercial appliance

Before you book,
in this order.

Each step comes from Continental Refrigerator's own guidance for Loc on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Press and hold any key until Loc changes to UnL.

02

Make your change within 30 seconds, before the keys lock again.

03

If the keypad will not unlock or no key responds, book a visit.

Cleared?

The code is gone from the controller, the box pulls down to its set point and holds it, the vat or the cavity reaches temperature and recovers on schedule, the rinse hits its heat and the drum finishes its spin, all without a new part. If the same code comes back within a week, or during the next busy shift, mention it when you book.

What not to do

Loc is not a failure of the control and does not affect cooling. A display that is blank or frozen is a different problem.

What you may
notice with it.

The commercial appliance problem Loc tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

No repair indicated

Nothing to repair.

Nothing on the unit has broken; the controller is reporting a state it chose or one somebody set. A defrost pauses cooling for a scheduled melt and shows a warmer air reading for a while, a combi asks for a delime or runs its clean cycle and locks the door until it ends, a dish machine or a laundry machine sits in energy save between busy periods, and a door-open reminder beeps after a long delivery. No part is needed: letting the cycle finish, or the key sequence in the manual, brings the unit back.

In Continental Refrigerator's own words

Loc will initially be displayed.
Continental Refrigerator operations manual, EVCO electronic control (rev. 07/22/2025) Continental Refrigerator operations manual, EVCO electronic control (rev. 07/22/2025)

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Described in Continental's EVCO electronic control operations manual (rev. 07/22/2025).

Continental Refrigerator Loc commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas
A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about Loc.

Can I clear Loc myself?
Press and hold any key until Loc changes to UnL.
Why does my Continental say Loc when I press a button?
The keypad locked itself after 30 seconds without use. Hold the key until UnL appears.
Can I stop the Continental keypad from locking?
The lock protects the settings from bumps during cleaning and service. We suggest leaving it on.
Does Loc stop my Continental from cooling?
No. Only the buttons are locked; the control keeps running the unit.

Back to your everyday

Still showing Loc?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

(844) 571-4566 Schedule a repair