Speed Queen E door: the door was pulled open during a cycle
Speed Queen shows E door when its door-open and door-locked signals are both active at once.
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: Speed Queen
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E door
actually means.
Speed Queen shows E door when its door-open and door-locked signals are both active at once. The manual names pulling on the door while it is locked or about to lock as a cause, along with a door lock system that is not working. Power must be removed to clear it.
Speed Queen commercial appliance display · also shown as E dOOr
What to do when E door shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeSpeed Queen
A Speed Queen machine in a laundromat or apartment laundry room is often booked for a weekday morning, when the fewest customers are waiting.
SourceSpeed Queen commercial front-load vended models, control manual 807870ENR5 (Alliance Laundry Systems)
Speed Queen commercial front-load vended and card models listed in manual 807870ENR5, such as SFNNCASP116TW01 and STGNXASP116TW01.
Before you book,
in this order.
Each step comes from Speed Queen's own guidance for E door on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Ask whether a customer tugged the door just after pressing start.
Turn the machine off, wait, and turn it on to clear E door.
If it returns without anyone touching the door, book a visit for the lock system.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
E door is not the plain CLoSE door prompt, which only asks for the door to be shut before a cycle. It is also not E dL, which reports the lock releasing mid-cycle.
What you may
notice with it.
The commercial appliance problem E door tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E door usually leads
Commercial controls and board repair.
Speed Queen
commercial appliances.
A Speed Queen machine in a laundromat or apartment laundry room is often booked for a weekday morning, when the fewest customers are waiting.
Speed Queen commercial appliance repairMore Speed Queen codes
All 14 Speed Queen codesControls and power on other makes
In Speed Queen's own words
Can be caused by pulling on door while locked or about to lock.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Speed Queen commercial front-load vended and card models listed in manual 807870ENR5, such as SFNNCASP116TW01 and STGNXASP116TW01.
Speed Queen E door commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E door.
Can I clear E door myself?
How do I stop E door codes at my laundromat?
Does E door on a Speed Queen damage the machine?
Why does a Speed Queen need a full power cycle after E door?
Back to your everyday
Still showing E door?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.