Dexter F14: over-current at the drive
F14 means the drive detected over-current.
Mon–Sat, 8am–8pm
- Motors and drives
- Commercial laundry machine repair
- Source: Dexter
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F14
actually means.
F14 means the drive detected over-current. Dexter's checks are whether the drum turns freely, whether the motor or bearings drag, whether the motor leads short, and whether the braking resistors read correctly.
Dexter commercial appliance display · also shown as DRIVE OC
What to do when F14 shows on the commercial applianceKind of codeMotors and drives
Something that should turn is not turning, or not at the speed the controller expects. A washer-extractor's drive or its inverter may stop the spin when the load is out of balance or a bearing drags, a tumbler's belt may slip so the drum barely moves, a convection or combi fan may slow on worn bearings and bake unevenly, and a dish machine's wash pump may hum without spraying. Redistributing a load, confirming the door is latched and running the machine's own test cycle are fair; a drum, a belt or a motor is a visit, and nobody reaches into a drum that could still move.
Usually leads toCommercial laundry machine repair
Coin, card and on-premise laundry machines and tumblers: door locks, bearings, inverters, burners and payment hardware.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeDexter
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
SourceDexter common troubleshooting and error code reference for T-Series vended front-loads (Part 8533, 9/19)
Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Before you book,
in this order.
Each step comes from Dexter's own guidance for F14 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Write down the drive light code before powering off.
Power down for three minutes and try one cycle with a normal load.
Book a visit if F14 returns; turning the drum by hand and testing the motor happen with power locked out.
Still there?
It usually turns into commercial laundry machine repair. Book with the code and the model number.
What not to do
F14 is not an overload of laundry alone, although a stuffed drum adds strain. F17 is the drive's separate overload message.
What you may
notice with it.
The commercial appliance problems F14 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where F14 usually leads
Commercial laundry machine repair.
Dexter
commercial appliances.
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
Dexter commercial appliance repairMore Dexter codes
All 15 Dexter codesMotors and drives on other makes
In Dexter's own words
This error is an over-current on the VF drive
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Dexter F14 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F14.
Can I clear F14 myself?
Can worn bearings cause F14 on a Dexter?
Is F14 on a Dexter a wiring problem?
Does F14 damage a Dexter drive?
Back to your everyday
Still showing F14?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.