Dexter F15: over-voltage inside the drive
Dexter explains F15 as either an incoming supply problem or the motor acting like a generator during braking.
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: Dexter
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F15
actually means.
Dexter explains F15 as either an incoming supply problem or the motor acting like a generator during braking. Supply voltage, braking resistor connections and resistor values are checked, and a high-leg 240 V supply gets special attention.
Dexter commercial appliance display · also shown as DRIVE OV
What to do when F15 shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeDexter
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
SourceDexter common troubleshooting and error code reference for T-Series vended front-loads (Part 8533, 9/19)
Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Before you book,
in this order.
Each step comes from Dexter's own guidance for F15 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Note whether other equipment in the store flickers or trips.
Power down for three minutes and try again.
Book a visit if F15 returns; supply and resistor checks need meters at the panel.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
F15 is not a low-voltage condition; F19 covers that. It does not mean the building wiring is unsafe, but an electrician may be needed if the supply is out of range.
What you may
notice with it.
The commercial appliance problem F15 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where F15 usually leads
Commercial controls and board repair.
Dexter
commercial appliances.
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
Dexter commercial appliance repairMore Dexter codes
All 15 Dexter codesControls and power on other makes
In Dexter's own words
This error is over-voltage on the VF drive
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Dexter F15 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F15.
Can I clear F15 myself?
Why does Dexter mention high-leg 240 V for F15?
Can braking resistors cause F15 on a Dexter?
Should I call an electrician for F15 on a Dexter?
Back to your everyday
Still showing F15?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.