Dexter F2: slow fill, the low level took over 7 minutes
Dexter reports a slow fill with F2 and keeps washing.
Mon–Sat, 8am–8pm
- Water, fill and drain
- Dish machine repair
- Source: Dexter
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F2
actually means.
Dexter reports a slow fill with F2 and keeps washing. Owners see it flash on the display; the causes Dexter lists are water valves, incoming pressure, blocked flow and a drain valve that is not closing.
Dexter commercial appliance display · also shown as SLOW FILL ERROR
What to do when F2 shows on the commercial applianceKind of codeWater, fill and drain
Water is not arriving, not reaching its level, not heating or not leaving on time. A dish machine may be short of fill because a supply valve is half closed or its line strainer is clogged, it may drain slowly through a scrap basket full of debris, or its booster may be too scaled to heat the rinse; a combi's steam generator may be scaled or its water treatment exhausted; a washer-extractor may time out on a slow drain. Opening the supply valve, cleaning strainers with the unit off and checking the drain line are fair; a pump, a fill valve, a heater or a leak near wiring is a visit.
Usually leads toDish machine repair
Undercounter, door-type and conveyor dish machines: tank heaters, boosters, wash pumps, fill and drain valves.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeDexter
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
SourceDexter common troubleshooting and error code reference for T-Series vended front-loads (Part 8533, 9/19)
Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Before you book,
in this order.
Each step comes from Dexter's own guidance for F2 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Check that the building's water supply to the machine is fully open.
Compare with neighboring machines to rule out a store-wide pressure drop.
Book a visit if only this machine is slow, so valves and inlet screens can be checked.
What not to do
F2 on a Dexter front-load is a fill warning; on a Dexter tumbler, F2 means an open temperature sensor. It does not stop the cycle the way a door lock error does.
What you may
notice with it.
The commercial appliance problem F2 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where F2 usually leads
Dish machine repair.
Dexter
commercial appliances.
A Dexter call in a laundromat is often set for opening time, before customers load the row and every pocket of the room is in use.
Dexter commercial appliance repairMore Dexter codes
All 15 Dexter codesWater, fill and drain on other makes
In Dexter's own words
This error is when a low water level is not reach within 7 minutes.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Dexter T-Series vended front-load machines (T-300 through T-1450) covered by Dexter's 2019 troubleshooting reference; the drive codes come from the variable frequency drive these models use.
Dexter F2 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F2.
Can I clear F2 myself?
Why does my Dexter keep washing with F2 showing?
Can a drain valve cause F2 on a Dexter?
Does F2 clear on its own on a Dexter?
Back to your everyday
Still showing F2?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.