Miele Professional Little Giants drain message: water did not pump out of the laundry machine
The PWM 908 stops its program when it cannot empty the drum.
Mon–Sat, 8am–8pm
- Water, fill and drain
- Dish machine repair
- Source: Miele Professional
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Drainage fault
actually means.
The PWM 908 stops its program when it cannot empty the drum. Miele names a blocked drain filter or pump and a drain hose fixed too high as the causes, and gives a maximum drain height of about one meter.
Miele Professional commercial appliance display
What to do when Drainage fault shows on the commercial applianceKind of codeWater, fill and drain
Water is not arriving, not reaching its level, not heating or not leaving on time. A dish machine may be short of fill because a supply valve is half closed or its line strainer is clogged, it may drain slowly through a scrap basket full of debris, or its booster may be too scaled to heat the rinse; a combi's steam generator may be scaled or its water treatment exhausted; a washer-extractor may time out on a slow drain. Opening the supply valve, cleaning strainers with the unit off and checking the drain line are fair; a pump, a fill valve, a heater or a leak near wiring is a visit.
Usually leads toDish machine repair
Undercounter, door-type and conveyor dish machines: tank heaters, boosters, wash pumps, fill and drain valves.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeMiele Professional
Miele Professional machines in a small business laundry are usually visited at the start of the day, before the first full load.
SourceMiele Professional PWM 908 Little Giants laundry machine operating and installation instructions, en-US M.-Nr. 12 805 440 (media.miele.com)
Miele Professional PWM 908 Little Giants machines with electric heating and drain pump or drain valve (en-US instructions M.-Nr. 12 805 440).
Before you book,
in this order.
Each step comes from Miele Professional's own guidance for Drainage fault on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Do not open the door with water in the drum; follow the manual's section on opening the door with a blocked drain.
Check the drain hose route and its height behind the machine, which must stay within the limit Miele gives.
Cleaning the drain filter and pump means releasing the water in the drum, so if staff have not been shown how, book a visit.
What not to do
This is a drain problem, not a leak; a leak shows Machine is leaking or triggers the Waterproof message. On drain-valve models the cause can be the valve rather than a pump.
What you may
notice with it.
The commercial appliance problems Drainage fault tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where Drainage fault usually leads
Dish machine repair.
Miele Professional
commercial appliances.
Miele Professional machines in a small business laundry are usually visited at the start of the day, before the first full load.
Miele Professional commercial appliance repairMore Miele Professional codes
Water, fill and drain on other makes
Commercial dish machines
Undercounter, door-type and conveyor dish machines with their booster heaters and chemical feeds, the warewashing station that washes and sanitizes every rack before it goes back on the line.
Commercial laundry equipment
Coin, card and app-paid front-load machines, washer-extractors, stacked units and tumble dryers in laundromats, multi-housing laundry rooms, hotels, gyms and on-premise laundries.
In Miele Professional's own words
The drain is blocked or restricted.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Miele Professional PWM 908 Little Giants machines with electric heating and drain pump or drain valve (en-US instructions M.-Nr. 12 805 440).
Miele Professional Drainage fault commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Drainage fault.
Can I clear Drainage fault myself?
Why won't the Miele Little Giants door open after a drain message?
What usually blocks the drain on a Miele PWM 908 in a salon or clinic?
How high can the drain hose be on a Miele Little Giants?
Back to your everyday
Still showing Drainage fault?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.