CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
The open door of a cold stainless combi oven in a commercial kitchen, its empty racks in view and a thin core temperature probe hanging on its holder inside the cavity, nobody at the combi oven.

Rational Service 20.1: the hot air temperature probe has failed

The iCombi Pro reads the cooking cabinet temperature through a probe on the hot air side.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Sensors and probes
  • Commercial controls and board repair
  • Source: Rational

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What Service 20.1
actually means.

The iCombi Pro reads the cooking cabinet temperature through a probe on the hot air side. Service 20.1 reports that probe as defective. Without a trusted reading the oven stops cooking, which Rational shows as no cooking possible.

Rational commercial appliance display · also shown as 20.1

What to do when Service 20.1 shows on the commercial appliance

Kind of codeSensors and probes

A probe is handing the controller a reading it cannot trust, or none at all: a box or coil sensor torn loose from its clip, a fryer probe coated in carbon from oil left too long between filterings, a combi core probe with a kinked cable, or a connector gone green from steam and cleaning chemicals. The unit then runs on, stops, or shuts the heat or the cooling off to protect itself. Letting it cool and restarting it as the manual describes is fair; a probe that still reads wrong sits behind a panel, and that is a visit.

Usually leads toCommercial controls and board repair

Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeRational

A Rational visit is timed after the evening cleaning cycle, when the cabinet is cool and the display can be read without a load inside.

SourceRATIONAL iCombi Pro floor units 20-1/1 and 20-2/1, original instructions for use (US English)

Listed in the error message tables of the iCombi Pro floor unit instructions for use (models 20-1/1 and 20-2/1, US English edition).

Before you book,
in this order.

Each step comes from Rational's own guidance for Service 20.1 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Move the current load to another oven or hold it safely; this unit will not finish it.

02

Restart the oven a single time and watch if the number reappears at once.

03

Write down the serial number and software version from the message and book a visit.

Still there?

It usually turns into commercial controls and board repair. Book with the code and the model number.

What not to do

Service 20.1 is not the core temperature probe that goes into the food; that probe reports as Service 31.1 or 31.2. It also differs from 20.2 and 20.4, which belong to humidity measurement and still allow cooking.

What you may
notice with it.

The commercial appliance problems Service 20.1 tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first

It also comes with

Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where Service 20.1 usually leads

Commercial controls and board repair.

Controller, touch panel, probe or sensor, relay, contactor, power supply, door switch or interlock, tested before anything is changed · moderate.
Book a visit What the job involves

Rational
commercial appliances.

A Rational visit is timed after the evening cleaning cycle, when the cabinet is cool and the display can be read without a load inside.

Rational commercial appliance repair

More Rational codes

Service 10Service 11Service 25Service 28.2Service 29Service 31.1Service 32.1Service 40Service 41Service 42.1Service 47.1Service 50
All 15 Rational codes

Sensors and probes on other makes

Alto-Shaam E20Beverage-Air E01Blodgett Cavity Probe ErrorContinental Refrigerator E0Delfield E01Dexter TEMP SENSOR SHORTFrymaster E13Garland E21
All 61 codes of this kind
A working restaurant cooking line under a stainless ventilation hood, two stainless gas fryers with baskets hanging above the oil, a flat griddle and a combi oven with a glass door beside them, the equipment clearly the subject, a cook seen only from behind and shoulders down at the far end of the line, warm kitchen light, small blue flames visible under the griddle. Rational builds this

Commercial cooking equipment

Fryers, griddles, charbroilers, restaurant ranges, convection and combi ovens, steamers, kettles, holding cabinets and toasters, on gas or electric, that make up the hot side of a kitchen line.

In Rational's own words

The temperature probe is defective.
RATIONAL iCombi Pro floor units 20-1/1 and 20-2/1, original instructions for use (US English) RATIONAL iCombi Pro floor units 20-1/1 and 20-2/1, original instructions for use (US English)

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Listed in the error message tables of the iCombi Pro floor unit instructions for use (models 20-1/1 and 20-2/1, US English edition).

Rational Service 20.1 commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about Service 20.1.

Can I clear Service 20.1 myself?
Move the current load to another oven or hold it safely; this unit will not finish it. If it comes back, it needs a visit.
Can I cook on a Rational oven showing Service 20.1?
No. Rational marks this message as one where cooking is not possible, because the oven cannot read its own cabinet heat.
Is Service 20.1 the probe I stick into the meat?
No. The food probe has its own numbers, Service 31.1 and 31.2. Service 20.1 is the fixed probe that measures the cabinet air for hot air heating.
How is Service 20.1 on a Rational combi usually repaired?
A technician tests the probe and its wiring and replaces the part that has failed. The probe is matched to the serial number of your unit, so have that number ready when you book.

Back to your everyday

Still showing Service 20.1?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair