Garland E47: the induction griddle plate is too hot
Griddles and braising pans share the seven-flash row with E29, but Garland notes that on these units E47 means the plate is too hot.
Mon–Sat, 8am–8pm
- Temperature and alarms
- Reach-in and prep table repair
- Source: Garland
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E47
actually means.
Griddles and braising pans share the seven-flash row with E29, but Garland notes that on these units E47 means the plate is too hot.
Garland commercial appliance display · also shown as 7 short flashes after each long flash
What to do when E47 shows on the commercial applianceKind of codeTemperature and alarms
The controller has seen a temperature outside the band it was set for and is saying so: a box above its alarm point, a fryer vat or an oven cavity that tripped its high-limit, or a dish machine rinse that never came up to heat. Often the cause sits outside the unit, such as a door left open during a delivery, a coil packed with grease, a kitchen far hotter than the maker allows or a booster fed cold water. Checking the door, the coil and the air around the unit is fair; move the product if a cold box stays above 41°F, and book the visit.
Usually leads toReach-in and prep table repair
Reach-ins, pass-throughs, prep tables and blast chillers: gaskets, hinges, fans, thermostats, condensers and compressors.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeGarland
Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.
SourceGarland Induction Counter-Top Series dual base-line models GI-SH/DU/BA installation, operation and maintenance manual, part number 4532290 Rev 3
Garland induction griddles and braising pans (GI-SH/GR, GI-SH/DU/GR and related models).
Before you book,
in this order.
Each step comes from Garland's own guidance for E47 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Stop loading product and let the plate cool.
Lower the setpoint if the griddle has been running at maximum with little on it.
Keep product on the plate, or turn the setting down during slow periods.
Book a visit if E47 appears at normal settings with product on the plate.
Still there?
It usually turns into reach-in and prep table repair. Book with the code and the model number.
What not to do
E47 is not a failed sensor; that is E22 on griddles. It is also different from E29, which Garland uses for generator and wiring problems.
What you may
notice with it.
The commercial appliance problems E47 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E47 usually leads
Reach-in and prep table repair.
Garland
commercial appliances.
Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.
Garland commercial appliance repairMore Garland codes
Temperature and alarms on other makes
In Garland's own words
E47 on griddles/braising pans indicates that griddle plate is too hot.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Garland induction griddles and braising pans (GI-SH/GR, GI-SH/DU/GR and related models).
Garland E47 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E47.
Can I clear E47 myself?
Why does my Garland griddle show E47 between orders?
Is E47 on a Garland griddle a fire risk?
Does E47 mean the Garland thermostat has failed?
Back to your everyday
Still showing E47?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.