CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
A gray electrical disconnect box on a tiled commercial kitchen wall beside a stainless convection oven, the oven's heavy power cord running up to it, the disconnect handle set to off, nobody near it.

Garland E05: the power knob or its sensor has a problem

The knob on a Garland induction unit turns a potentiometer that tells the generator how much power to send.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Controls and power
  • Commercial controls and board repair
  • Source: Garland

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What E05
actually means.

The knob on a Garland induction unit turns a potentiometer that tells the generator how much power to send. When that part or the power switch reads wrong, the unit switches off and shows E05, or five short flashes after each long one. Garland's only action for it is a service call.

Garland commercial appliance display · also shown as 5 short flashes after each long flash

What to do when E05 shows on the commercial appliance

Kind of codeControls and power

The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.

Usually leads toCommercial controls and board repair

Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeGarland

Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.

SourceGarland Induction Counter-Top Series dual base-line models GI-SH/DU/BA installation, operation and maintenance manual, part number 4532290 Rev 3

Garland counter-top induction cook-tops, woks and griddles (GI-SH/DU/BA, GI-BH/BA, GI-SH/BA, GI-SH/GR). Units with a digital display show the E number; units with only an indicator lamp show the flash count instead.

Before you book,
in this order.

Each step comes from Garland's own guidance for E05 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Turn the knob back to off and switch the unit off at its power switch.

02

Wipe spills away from the knob so no liquid runs into it.

03

Switch back on once to see if E05 returns.

04

Book a visit if it does, since the switch or potentiometer needs replacement.

Still there?

It usually turns into commercial controls and board repair. Book with the code and the model number.

What not to do

E05 is not a cookware or overheating code, so changing the pan or letting the unit cool will not clear it. A knob that feels loose or gritty is a strong hint that E05 will follow.

What you may
notice with it.

The commercial appliance problem E05 tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first
Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where E05 usually leads

Commercial controls and board repair.

Controller, touch panel, probe or sensor, relay, contactor, power supply, door switch or interlock, tested before anything is changed · moderate.
Book a visit What the job involves

Garland
commercial appliances.

Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.

Garland commercial appliance repair

More Garland codes

E01E02E03E04E06E10E12E21E22E29E47

Controls and power on other makes

Alto-Shaam E02Beverage-Air uLiBlodgett Com ErrorDelfield uLiDexter F1Frymaster E19Hatco Communication ErrorHenny Penny E-4
All 61 codes of this kind
A working restaurant cooking line under a stainless ventilation hood, two stainless gas fryers with baskets hanging above the oil, a flat griddle and a combi oven with a glass door beside them, the equipment clearly the subject, a cook seen only from behind and shoulders down at the far end of the line, warm kitchen light, small blue flames visible under the griddle. Garland builds this

Commercial cooking equipment

Fryers, griddles, charbroilers, restaurant ranges, convection and combi ovens, steamers, kettles, holding cabinets and toasters, on gas or electric, that make up the hot side of a kitchen line.

In Garland's own words

Power switch/potentiometer error.
Garland Induction Counter-Top Series dual base-line models GI-SH/DU/BA installation, operation and maintenance manual, part number 4532290 Rev 3

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Garland counter-top induction cook-tops, woks and griddles (GI-SH/DU/BA, GI-BH/BA, GI-SH/BA, GI-SH/GR). Units with a digital display show the E number; units with only an indicator lamp show the flash count instead.

Garland E05 commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about E05.

Can I clear E05 myself?
Turn the knob back to off and switch the unit off at its power switch. If it comes back, it needs a visit.
Can spilled liquid cause E05 on a Garland?
It can. Liquid that runs down a knob shaft can reach the potentiometer. Keep the knob area wiped dry.
Is E05 on a Garland a quick repair?
It usually means replacing the potentiometer or switch, which is a routine part change for a technician.
Can I use the Garland with E05 if it comes back on?
If the unit restarts and responds normally to the knob, you can finish the service carefully, but book the repair.

Back to your everyday

Still showing E05?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair