Garland E10: an internal electronic failure
E10, or ten short flashes after each long one, is Garland's code for an internal electronic failure.
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: Garland
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E10
actually means.
E10, or ten short flashes after each long one, is Garland's code for an internal electronic failure. Depending on the cause the unit switches off at once or keeps running in a power reduction mode. There is no staff step for it beyond calling for service.
Garland commercial appliance display · also shown as 10 short flashes after each long flash
What to do when E10 shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeGarland
Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.
SourceGarland Induction Counter-Top Series dual base-line models GI-SH/DU/BA installation, operation and maintenance manual, part number 4532290 Rev 3
Garland counter-top induction cook-tops, woks and griddles (GI-SH/DU/BA, GI-BH/BA, GI-SH/BA, GI-SH/GR). Units with a digital display show the E number; units with only an indicator lamp show the flash count instead.
Before you book,
in this order.
Each step comes from Garland's own guidance for E10 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Switch the unit off at its power switch.
Move cooking to another zone or piece of equipment.
Note whether the unit shut off or kept running at low power.
Book a visit and give the code and what happened.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
E10 is not caused by the pan or by the air around the unit, so cooling it down will not help. It also differs from E12, which is a heat warning that reduces power rather than a failure.
What you may
notice with it.
The commercial appliance problem E10 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E10 usually leads
Commercial controls and board repair.
Garland
commercial appliances.
Garland equipment on a cooking line is usually looked at after close, when every burner is cold and the grates can come up without rushing a cook.
Garland commercial appliance repairMore Garland codes
Controls and power on other makes
In Garland's own words
Internal electronic failure.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Garland counter-top induction cook-tops, woks and griddles (GI-SH/DU/BA, GI-BH/BA, GI-SH/BA, GI-SH/GR). Units with a digital display show the E number; units with only an indicator lamp show the flash count instead.
Garland E10 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E10.
Can I clear E10 myself?
Can I keep using a Garland that shows E10 at low power?
Does E10 mean the Garland generator must be replaced?
Why did my Garland show E10 after a power outage?
Back to your everyday
Still showing E10?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.