UniMac E do: the control saw the door open while locked
E do ends the cycle and needs a power-down to clear.
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: UniMac
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E do
actually means.
E do ends the cycle and needs a power-down to clear. UniMac names pulling on the door during locking as the usual cause and asks for the locking system to be corrected when it happens without that.
UniMac commercial appliance display · also shown as E dO
What to do when E do shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeUniMac
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
SourceUniMac UW-series washer-extractor control manual F8552201R2 (Alliance Laundry Systems, 2017)
UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
Before you book,
in this order.
Each step comes from UniMac's own guidance for E do on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Remind staff not to pull the handle after pressing start.
Power the machine down to clear E do and restart the load.
If E do returns with nobody touching the door, book a visit to check the lock and door switch.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
E do is not the plain door message, which only asks for the door to be shut before starting. It also differs from E dL, where the lock does not respond at all.
What you may
notice with it.
The commercial appliance problem E do tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E do usually leads
Commercial controls and board repair.
UniMac
commercial appliances.
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
UniMac commercial appliance repairMore UniMac codes
All 15 UniMac codesControls and power on other makes
In UniMac's own words
Control detects door open. Caused by pulling on door while locked or about to lock.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
UniMac E do commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E do.
Can I clear E do myself?
Why does E do show up after staff changes on a UniMac?
Does E do lose the wash on a UniMac?
What part fails when E do keeps returning on a UniMac?
Back to your everyday
Still showing E do?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.