UniMac E FS: the frame stability switch opened
UniMac extractors carry a frame stability switch that trips if the machine moves more than it should.
Mon–Sat, 8am–8pm
- Sensors and probes
- Commercial controls and board repair
- Source: UniMac
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E FS
actually means.
UniMac extractors carry a frame stability switch that trips if the machine moves more than it should. E FS ends the cycle; loose anchor bolts, a cracked base or a badly out-of-balance load can all open it.
UniMac commercial appliance display · also shown as EFS
What to do when E FS shows on the commercial applianceKind of codeSensors and probes
A probe is handing the controller a reading it cannot trust, or none at all: a box or coil sensor torn loose from its clip, a fryer probe coated in carbon from oil left too long between filterings, a combi core probe with a kinked cable, or a connector gone green from steam and cleaning chemicals. The unit then runs on, stops, or shuts the heat or the cooling off to protect itself. Letting it cool and restarting it as the manual describes is fair; a probe that still reads wrong sits behind a panel, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeUniMac
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
SourceUniMac UW-series washer-extractor control manual F8552201R2 (Alliance Laundry Systems, 2017)
UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
Before you book,
in this order.
Each step comes from UniMac's own guidance for E FS on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Stop using the machine and look at the floor around its base for movement or cracked grout.
Unload the machine once the door unlocks and reload it evenly.
Book a visit if E FS returns; mounting bolts and the base are checked with tools.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
E FS is not E Ub, which reports a load that would not balance before extract. A machine that has visibly shifted on its base should not run again until it is re-secured.
What you may
notice with it.
The commercial appliance problems E FS tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E FS usually leads
Commercial controls and board repair.
UniMac
commercial appliances.
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
UniMac commercial appliance repairMore UniMac codes
All 15 UniMac codesSensors and probes on other makes
In UniMac's own words
Control detects Frame Stability Switch open. End cycle.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
UniMac E FS commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E FS.
Can I clear E FS myself?
Why does a hardmount UniMac need to be bolted down?
Can a heavy load trip E FS on a UniMac?
Is E FS a safety code on a UniMac?
Back to your everyday
Still showing E FS?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.