CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
A stainless door-type dish machine in a restaurant dish room with its hood raised and its wash chamber empty, a clean wire rack on the landing table beside it, the tiled floor dry, nobody at the dish machine.

Hobart 032: the booster did not fill in time

Every LXn cycle starts by filling the booster.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Water, fill and drain
  • Dish machine repair
  • Source: Hobart

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What 032
actually means.

Every LXn cycle starts by filling the booster. If the level is not reached in time, the screen reads Fill error, inspect incoming water line with 032. Hobart asks for the supply valve, the fill hose and the water pressure to be checked first.

Hobart commercial appliance display · also shown as Error 032

What to do when 032 shows on the commercial appliance

Kind of codeWater, fill and drain

Water is not arriving, not reaching its level, not heating or not leaving on time. A dish machine may be short of fill because a supply valve is half closed or its line strainer is clogged, it may drain slowly through a scrap basket full of debris, or its booster may be too scaled to heat the rinse; a combi's steam generator may be scaled or its water treatment exhausted; a washer-extractor may time out on a slow drain. Opening the supply valve, cleaning strainers with the unit off and checking the drain line are fair; a pump, a fill valve, a heater or a leak near wiring is a visit.

Usually leads toDish machine repair

Undercounter, door-type and conveyor dish machines: tank heaters, boosters, wash pumps, fill and drain valves.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeHobart

A Hobart dish machine that stops holding its rinse heat is usually seen right after the lunch racks clear, so the tank can drain and cool.

SourceHobart LXn / LXGn series instructions manual F41243 (10-23), error code chart

Hobart LXn and LXGn undercounter machines (LXnC, LXnH, LXnR, LXGnPR, LXGnR) with the touchscreen control, per instructions manual F41243. AM16, CL and FT2000 machines use their own displays and are not covered by this chart.

Before you book,
in this order.

Each step comes from Hobart's own guidance for 032 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Make sure the water supply valve under or behind the machine is fully open.

02

Straighten the fill hose if it is kinked or crushed behind the machine.

03

Press ENTER to clear the message and let the machine try again.

04

If 032 returns, have the water pressure checked and book a visit for the fill valve.

Still there?

It usually turns into dish machine repair. Book with the code and the model number.

What not to do

032 is not a slow booster heater; that is 003. It also differs from 033, where the fill valve stays open too long rather than the tank filling too slowly.

What you may
notice with it.

The commercial appliance problems 032 tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first

It also comes with

Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where 032 usually leads

Dish machine repair.

Dish machine tank heater or booster element, thermostat, fill valve, float switch, drain valve, wash pump seal or motor, conveyor drive · moderate.
Book a visit What the job involves

Hobart
commercial appliances.

A Hobart dish machine that stops holding its rinse heat is usually seen right after the lunch racks clear, so the tank can drain and cool.

Hobart commercial appliance repair

More Hobart codes

003019021029033035038049057070074080
All 15 Hobart codes

Water, fill and drain on other makes

Alto-Shaam E01Blodgett Water Level ErrorCleveland LOW WATER lightDexter F2Frymaster E33Hatco LO H2OMiele Professional F18Pitco DRAINING TURN OFF
All 44 codes of this kind
A stainless door-type dish machine in a busy restaurant warewashing station, its hood half raised with steam rising, a green plastic rack of clean white plates sliding out onto the clean-side table, the dish machine clearly the subject, a worker seen only from behind and shoulders down in an apron at the soiled side, bright even kitchen light. Hobart builds this

Commercial dish machines

Undercounter, door-type and conveyor dish machines with their booster heaters and chemical feeds, the warewashing station that washes and sanitizes every rack before it goes back on the line.

In Hobart's own words

Fill error, inspect incoming water line.
Hobart LXn / LXGn series instructions manual F41243 (10-23), error code chart Hobart LXn / LXGn series instructions manual F41243 (10-23), error code chart

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Hobart LXn and LXGn undercounter machines (LXnC, LXnH, LXnR, LXGnPR, LXGnR) with the touchscreen control, per instructions manual F41243. AM16, CL and FT2000 machines use their own displays and are not covered by this chart.

Hobart 032 commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about 032.

Can I clear 032 myself?
Make sure the water supply valve under or behind the machine is fully open. If it comes back, it needs a visit.
What water pressure does a Hobart LXn need?
Hobart lists 15 to 65 psi at the incoming line. Pressure below that range fills too slowly, and a plumber can fit a regulator or booster pump if the building supply is outside it.
Can a clogged filter on the water line cause 032?
Yes, a water treatment cartridge or inlet screen that is due for change slows the fill the same way a half-closed valve does.
Why does 032 show only when the kitchen is busy?
Other fixtures on the same line can pull the pressure down at peak times. The pattern is worth mentioning when you book the visit.

Back to your everyday

Still showing 032?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair