UniMac Ed06: the motor drive is too hot
Ed06 is the motor drive's thermal message on 45 and 65 lb UniMac extractors.
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: UniMac
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Ed06
actually means.
Ed06 is the motor drive's thermal message on 45 and 65 lb UniMac extractors. UniMac asks for air to move freely around the drive's heat sink; lint build-up inside the machine and a hot, closed laundry room are common reasons it cannot cool.
UniMac commercial appliance display · also shown as Ed 06
What to do when Ed06 shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeUniMac
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
SourceUniMac UW-series washer-extractor control manual F8552201R2 (Alliance Laundry Systems, 2017)
UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
Before you book,
in this order.
Each step comes from UniMac's own guidance for Ed06 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Power the machine down and let it cool.
Make sure the laundry room is ventilated and nothing blocks airflow around the machine.
Book a visit to clean lint from the drive heat sink if Ed06 returns.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
Ed06 is about the drive electronics, not the motor windings or the wash water. It is not E Ht, which reports water that could not be heated.
What you may
notice with it.
The commercial appliance problem Ed06 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where Ed06 usually leads
Commercial controls and board repair.
UniMac
commercial appliances.
UniMac equipment in a facility laundry room is usually serviced after the heaviest morning loads are out.
UniMac commercial appliance repairMore UniMac codes
All 15 UniMac codesControls and power on other makes
In UniMac's own words
The control detects a high IPM temperature. Power down, verify convection around drive heat sink
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. UniMac UW-series hardmount extractors of 45 to 130 lb (UWH, UWL, UWN and UWU models) with the keypad control in manual F8552201. Current UW models sold with UniLinc Touch show plain-word messages instead of these codes.
UniMac Ed06 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Ed06.
Can I clear Ed06 myself?
Why does Ed06 appear in summer on a UniMac?
Is Ed06 on a UniMac a fire risk?
Can I clean the UniMac drive myself?
Back to your everyday
Still showing Ed06?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.