CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
A stainless sandwich prep table on a restaurant line, the prep table's lid raised over a row of covered food pans, a probe thermometer standing in one pan, nobody at the table.

Frymaster E44: the vat took too long to recover its heat

The FQ4000 times how long the oil takes to rise through a set band after a load goes in.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Temperature and alarms
  • Reach-in and prep table repair
  • Source: Frymaster

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What E44
actually means.

The FQ4000 times how long the oil takes to rise through a set band after a load goes in. If that time runs past the limit, it logs E44 and sounds the alarm; on the gas FilterQuick the limit in the manual is 3:15. When the same thing happens on two or more cycles, the controller moves up to E45 and asks for service.

Frymaster commercial appliance display · also shown as E25 (M3000)

What to do when E44 shows on the commercial appliance

Kind of codeTemperature and alarms

The controller has seen a temperature outside the band it was set for and is saying so: a box above its alarm point, a fryer vat or an oven cavity that tripped its high-limit, or a dish machine rinse that never came up to heat. Often the cause sits outside the unit, such as a door left open during a delivery, a coil packed with grease, a kitchen far hotter than the maker allows or a booster fed cold water. Checking the door, the coil and the air around the unit is fair; move the product if a cold box stays above 41°F, and book the visit.

Usually leads toReach-in and prep table repair

Reach-ins, pass-throughs, prep tables and blast chillers: gaskets, hinges, fans, thermostats, condensers and compressors.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeFrymaster

A Frymaster fryer is serviced cold: the visit waits until the oil has come down and the vat has been drained by the crew.

SourceFrymaster FilterQuick FQG30U easyTouch gas fryer manual with FQ4000 controller (error log codes, section 5.6)

FQ4000 easyTouch touchscreen controller on FilterQuick fryers (FQG30U and related FilterQuick gas and electric models). The M3000 logs recovery as E25 with a limit of 1:40 for electric and 2:25 for gas fryers.

Before you book,
in this order.

Each step comes from Frymaster's own guidance for E44 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Press the check button to silence the alarm and clear the message.

02

Check the oil level against the fill lines and avoid loading more frozen product than the recipe calls for.

03

If E44 keeps coming back or E45 appears, book a visit; slow recovery often traces back to a dirty blower, a weak burner or a failing element.

Still there?

It usually turns into reach-in and prep table repair. Book with the code and the model number.

What not to do

E44 is a slow heat-up, not a refusal to heat: when the burner will not light at all, the controller logs E28. A single E44 after an unusually large load is less telling than E45, which is the repeat.

What you may
notice with it.

The commercial appliance problems E44 tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first

It also comes with

Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where E44 usually leads

Reach-in and prep table repair.

Reach-in, pass-through or prep table gasket, hinge, fan motor, thermostat or controller, defrost heater, leak repair or compressor · moderate.
Book a visit What the job involves

Frymaster
commercial appliances.

A Frymaster fryer is serviced cold: the visit waits until the oil has come down and the vat has been drained by the crew.

Frymaster commercial appliance repair

More Frymaster codes

E13E16E17E18E19E25E28E33E39E41E42E53
All 15 Frymaster codes

Temperature and alarms on other makes

Alto-Shaam E13Beverage-Air HiBlodgett Cavity High Temp ErrorCleveland RESET lightContinental Refrigerator HIDelfield HiGarland E04Hatco Control Board Overtemp
All 68 codes of this kind
A working restaurant cooking line under a stainless ventilation hood, two stainless gas fryers with baskets hanging above the oil, a flat griddle and a combi oven with a glass door beside them, the equipment clearly the subject, a cook seen only from behind and shoulders down at the far end of the line, warm kitchen light, small blue flames visible under the griddle. Frymaster builds this

Commercial cooking equipment

Fryers, griddles, charbroilers, restaurant ranges, convection and combi ovens, steamers, kettles, holding cabinets and toasters, on gas or electric, that make up the hot side of a kitchen line.

In Frymaster's own words

Recovery time exceeded maximum time
Frymaster FilterQuick FQG30U easyTouch gas fryer manual with FQ4000 controller (error log codes, section 5.6) Frymaster FilterQuick FQG30U easyTouch gas fryer manual with FQ4000 controller (error log codes, section 5.6) Frymaster Manual LOV M3000 controller operation manual, 02/2025 (E-log error codes)

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. FQ4000 easyTouch touchscreen controller on FilterQuick fryers (FQG30U and related FilterQuick gas and electric models). The M3000 logs recovery as E25 with a limit of 1:40 for electric and 2:25 for gas fryers.

Frymaster E44 commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about E44.

Can I clear E44 myself?
Press the check button to silence the alarm and clear the message. If it comes back, it needs a visit.
How do I silence the slow recovery alarm on a Frymaster?
Press the check button on the FQ4000 (the YES or numbered button on older controllers). That clears the message but not whatever slowed the heat-up.
What is a normal recovery time on a Frymaster?
The FQ4000 gas manual gives 3:15 as the maximum, and the M3000 manual gives 1:40 for electric and 2:25 for gas. The INFO button shows each vat's last recovery time.
Why is my Frymaster slow to recover only at lunch?
Big frozen loads pull the oil down further than the control can recover inside the limit. If it happens with normal loads, the heat source needs a look.

Back to your everyday

Still showing E44?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair