CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
A gray electrical disconnect box on a tiled commercial kitchen wall beside a stainless convection oven, the oven's heavy power cord running up to it, the disconnect handle set to off, nobody near it.

Henny Penny E-26: heat stuck on in an electric pressure fryer

On the electric PFE models the control watches element current.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Controls and power
  • Commercial controls and board repair
  • Source: Henny Penny

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What E-26
actually means.

On the electric PFE models the control watches element current. If current flows while heat should be off, a contactor or the board is stuck, and the fryer shows E-26. Henny Penny warns it can appear even with the power switch off, so the switch alone may not stop the heat.

Henny Penny commercial appliance display

What to do when E-26 shows on the commercial appliance

Kind of codeControls and power

The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.

Usually leads toCommercial controls and board repair

Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeHenny Penny

Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.

SourceHenny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls)

Henny Penny PFE 500 and PFE 561 electric pressure fryers with the C1000 or C8000 control (operator manual FM05-011R); electric models only.

Before you book,
in this order.

Each step comes from Henny Penny's own guidance for E-26 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Unplug the fryer or switch off its circuit breaker from a dry panel; the power switch alone may not stop the elements.

02

Keep watch on the oil and keep the Class K extinguisher at hand until it cools; if there is smoke or flame, use the suppression system and call 911.

03

Book a visit so the contactors and the control board can be checked before the fryer is used again.

Still there?

It usually turns into commercial controls and board repair. Book with the code and the model number.

What not to do

E-26 is heat locked on, which is more serious than current reading high (E-25) or low (E-27). It is not an oil overheat reading, though it can lead to one.

What you may
notice with it.

The commercial appliance problems E-26 tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first

It also comes with

Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where E-26 usually leads

Commercial controls and board repair.

Controller, touch panel, probe or sensor, relay, contactor, power supply, door switch or interlock, tested before anything is changed · moderate.
Book a visit What the job involves

Henny Penny
commercial appliances.

Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.

Henny Penny commercial appliance repair

More Henny Penny codes

E-4E-5E-6AE-6BE-10E-15E-20AE-20BE-20CE-20DE-25E-27
All 16 Henny Penny codes

Controls and power on other makes

Alto-Shaam E02Beverage-Air uLiBlodgett Com ErrorDelfield uLiDexter F1Frymaster E19Garland E01Hatco Communication Error
All 58 codes of this kind
A working restaurant cooking line under a stainless ventilation hood, two stainless gas fryers with baskets hanging above the oil, a flat griddle and a combi oven with a glass door beside them, the equipment clearly the subject, a cook seen only from behind and shoulders down at the far end of the line, warm kitchen light, small blue flames visible under the griddle. Henny Penny builds this

Commercial cooking equipment

Fryers, griddles, charbroilers, restaurant ranges, convection and combi ovens, steamers, kettles, holding cabinets and toasters, on gas or electric, that make up the hot side of a kitchen line.

In Henny Penny's own words

Heat amps locked on
Henny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls) Henny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls) Henny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls)

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Henny Penny PFE 500 and PFE 561 electric pressure fryers with the C1000 or C8000 control (operator manual FM05-011R); electric models only.

Henny Penny E-26 commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about E-26.

Can I clear E-26 myself?
Unplug the fryer or switch off its circuit breaker from a dry panel; the power switch alone may not stop the elements. If it comes back, it needs a visit.
Why does a Henny Penny show E-26 with the switch off?
A contactor that has welded closed feeds the elements directly, bypassing the switch. That is why Henny Penny says to unplug it or turn off the breaker.
Is E-26 an emergency on a Henny Penny?
Treat it as one. Heat that cannot be switched off can drive the oil toward its smoke point, so cut the power at the breaker and watch the vat.
What gets replaced after E-26?
Usually a contactor, sometimes the control board. A technician checks both before the fryer goes back into service.

Back to your everyday

Still showing E-26?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair