CommercialApplianceRepair.center (844) 571-4566Mon–Sat, 8am–8pm Book a visit
The open door of a cold stainless combi oven in a commercial kitchen, its empty racks in view and a thin core temperature probe hanging on its holder inside the cavity, nobody at the combi oven.

Henny Penny E-6A: the oil temperature probe reads open

The fryer needs the probe reading to decide when to heat.

(844) 571-4566

Mon–Sat, 8am–8pm

  • Sensors and probes
  • Commercial controls and board repair
  • Source: Henny Penny

Book a visit

Three short steps, about a minute.

or call (844) 571-4566

What E-6A
actually means.

The fryer needs the probe reading to decide when to heat. When the circuit reads open, as with a broken probe or a loose connection, the control shows E-6A and will not run a normal cook cycle.

Henny Penny commercial appliance display · also shown as Oil prob open

What to do when E-6A shows on the commercial appliance

Kind of codeSensors and probes

A probe is handing the controller a reading it cannot trust, or none at all: a box or coil sensor torn loose from its clip, a fryer probe coated in carbon from oil left too long between filterings, a combi core probe with a kinked cable, or a connector gone green from steam and cleaning chemicals. The unit then runs on, stops, or shuts the heat or the cooling off to protect itself. Letting it cool and restarting it as the manual describes is fair; a probe that still reads wrong sits behind a panel, and that is a visit.

Usually leads toCommercial controls and board repair

Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.

Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.

MakeHenny Penny

Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.

SourceHenny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls)

Henny Penny PFE 500 and PFE 561 electric and PFG 600 gas pressure fryers with the C1000 or C8000 control (operator manual FM05-011R).

Before you book,
in this order.

Each step comes from Henny Penny's own guidance for E-6A on its commercial appliances. Follow it to the end: the last card says whether this is a visit.

01

Silence the alarm, switch the fryer off and back on as Henny Penny directs.

02

Write down whether the code came on at start-up or partway through a cook, which helps the technician.

03

If E-6A returns, stop using the fryer and book a visit for the probe and its wiring.

Still there?

It usually turns into commercial controls and board repair. Book with the code and the model number.

What not to do

E-6A is an open circuit, while the shorted version of the same probe shows E-6B. Neither one is about the high-limit thermostat, which reports as E-10.

What you may
notice with it.

The commercial appliance problems E-6A tends to arrive with. Answer these at the commercial appliance before anyone is booked.

All problems

Before you call

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

All 8 causes, cheapest first

It also comes with

Close view of the dark touch control panel on the front of a stainless combi oven in a commercial kitchen, one abstract amber warning indicator glowing among unlit icons, the steam-fogged glass door blurred beside it. Problem

Commercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display

8 causes, cheapest first

Where E-6A usually leads

Commercial controls and board repair.

Controller, touch panel, probe or sensor, relay, contactor, power supply, door switch or interlock, tested before anything is changed · moderate.
Book a visit What the job involves

Henny Penny
commercial appliances.

Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.

Henny Penny commercial appliance repair

More Henny Penny codes

E-4E-5E-6BE-10E-15E-20AE-20BE-20CE-20DE-25E-26E-27
All 16 Henny Penny codes

Sensors and probes on other makes

Alto-Shaam E20Beverage-Air E01Blodgett Cavity Probe ErrorContinental Refrigerator E0Delfield E01Dexter TEMP SENSOR SHORTFrymaster E13Garland E21
All 61 codes of this kind
A working restaurant cooking line under a stainless ventilation hood, two stainless gas fryers with baskets hanging above the oil, a flat griddle and a combi oven with a glass door beside them, the equipment clearly the subject, a cook seen only from behind and shoulders down at the far end of the line, warm kitchen light, small blue flames visible under the griddle. Henny Penny builds this

Commercial cooking equipment

Fryers, griddles, charbroilers, restaurant ranges, convection and combi ovens, steamers, kettles, holding cabinets and toasters, on gas or electric, that make up the hot side of a kitchen line.

In Henny Penny's own words

Temperature probe open
Henny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls) Henny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls)

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Henny Penny PFE 500 and PFE 561 electric and PFG 600 gas pressure fryers with the C1000 or C8000 control (operator manual FM05-011R).

Henny Penny E-6A commercial appliance repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A restaurant team working a busy commercial kitchen line.
For the heart of your home.

Questions
about E-6A.

Can I clear E-6A myself?
Silence the alarm, switch the fryer off and back on as Henny Penny directs. If it comes back, it needs a visit.
Can a Henny Penny pressure fryer run with E-6A showing?
No. Without a probe signal the control cannot hold oil temperature, so the fryer should stay off until the probe is tested.
Why does E-6A come and go on my Henny Penny?
An intermittent open usually means a cracked probe lead or a connector that loosens as the fryer heats and cools. A technician can check the probe resistance and the plug together.
Is E-6A the same as E-6B on a Henny Penny?
They point to the same probe but opposite readings: A is open, B is shorted. The repair is often the same part, but the test result tells the technician which way it failed.

Back to your everyday

Still showing E-6A?

A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.

Schedule a repair Call (844) 571-4566
(844) 571-4566 Schedule a repair