Henny Penny E-25: heat amps too high on an electric pressure fryer
The electric PFE models monitor element current and compare it with a nominal amps figure stored in special settings (SP-12).
Mon–Sat, 8am–8pm
- Controls and power
- Commercial controls and board repair
- Source: Henny Penny
Book a visit
Three short steps, about a minute.
or call (844) 571-4566
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E-25
actually means.
The electric PFE models monitor element current and compare it with a nominal amps figure stored in special settings (SP-12). A reading well above that figure raises E-25, pointing at the supply, wiring or elements.
Henny Penny commercial appliance display
What to do when E-25 shows on the commercial applianceKind of codeControls and power
The controller itself is reporting trouble, or the supply behind it is: a display with dead segments, a keypad that stopped responding after steam or degreaser got behind it, relays that stick, stored recipes or cycles that vanished overnight, a blown control fuse, or one leg of a three-phase feed missing so half the heat or the pump is gone. A full power cycle at the breaker, done as the manual describes, clears a passing glitch; a code that returns, a scorched smell or any sign of moisture behind the panel means the breaker stays off, and that is a visit.
Usually leads toCommercial controls and board repair
Controllers, touch panels, relays, contactors and interlocks tested, and replaced only when the evidence says so.
Shows up asCommercial Appliance Error Code on a Combi, Fryer, Dish Machine or Laundry Display
A commercial appliance error code appears as letters or numbers on a combi, fryer, reach-in controller, dish machine or laundry machine display, or as a flashing light or an alarm tone.
MakeHenny Penny
Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.
SourceHenny Penny FM05-011R operator manual, PFE 500 / PFE 561 / PFG 600 pressure fryers (C1000 and C8000 controls)
Henny Penny PFE 500 and PFE 561 electric pressure fryers with the C1000 or C8000 control (operator manual FM05-011R); electric models only.
Before you book,
in this order.
Each step comes from Henny Penny's own guidance for E-25 on its commercial appliances. Follow it to the end: the last card says whether this is a visit.
Silence the alarm and turn the fryer off.
Note whether other equipment on the same circuit was just added or moved, which the technician will ask about.
Book a visit: Henny Penny sends the check to the SP-12 setting, the electrical supply, the wiring and the elements.
Still there?
It usually turns into commercial controls and board repair. Book with the code and the model number.
What not to do
E-25 is too much current; the opposite, too little, is E-27, and heat stuck on is E-26. It is not an oil temperature reading.
What you may
notice with it.
The commercial appliance problems E-25 tends to arrive with. Answer these at the commercial appliance before anyone is booked.
All problems
Where E-25 usually leads
Commercial controls and board repair.
Henny Penny
commercial appliances.
Henny Penny equipment gets its visit once the unit is cool, any oil is down and the crew has logged the last load.
Henny Penny commercial appliance repairMore Henny Penny codes
All 16 Henny Penny codesControls and power on other makes
In Henny Penny's own words
Heats amps too high
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Henny Penny PFE 500 and PFE 561 electric pressure fryers with the C1000 or C8000 control (operator manual FM05-011R); electric models only.
Henny Penny E-25 commercial appliance repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E-25.
Can I clear E-25 myself?
What is SP-12 on a Henny Penny electric fryer?
Can a power problem in the building cause E-25?
Is it safe to run the fryer with E-25?
Back to your everyday
Still showing E-25?
A booking with a code goes further when it has the code as shown, the model and serial from the data plate, and a word on whether the unit still holds temperature, heats, rinses or spins. With those three, the office can match the likely part to your unit the same day.